站点导航
Index
型号列表
Type List
春雷热拼机(无胶喷绘布拼接机)概述
Introduction of Poster Heat Jointer without glue
网站首页
Home Page
样品展示
Sample show
服务指导
Service&Guide
联系我们
Contact us
汇款账号
Trade Payment

第四代4000K型
无胶热拼机
Hot-Air Welder Model4000K
第四代4000L型
无胶热拼机
Hot-Air Welder Model4000L

返回


502胶终结者,喷绘机伴侣--热拼机(无胶广告喷绘布拼接机)



  当喷绘画面超过喷绘机幅度时,就需要分次喷绘后再拼接,以及对海报的边缘的增强处理,传统上是采用502及其衍生型胶水等胶合剂的方式,存在胶合速度慢 和胶合强度不够的问题,比如:容易起泡起皱、弄脏画面、不均匀稳定,往往要进行特殊处理,比如打磨表面,才能得到良好强度,这样就影响了工作效率,并受温度和湿度影响,比如北方低温环境下胶合效果不好,且操作繁 琐、费工时,需要比较大块的工作场地。
  使用无胶广告喷绘布拼接机(热拼机),就能很好地解决以上诸多问题,免去使用胶合剂,且省工省时省事省场地,不论使用哪种布,灯箱布、枷网帆布等,不再受限制于高周波机器的平台长度,只要有一块相对平坦的耐热桌面或地面就可以随时作业,比如:长达200米的接缝都可 以一人在30见方的相对平坦的耐热桌面或地面就可以作业。
  该机基于瑞士LEISER的热风技术,采用自走热合原理,经过大量实践后进行了改进而定型,结构采取模块化组件,便于维护。
  该机体积小、轻巧,全重仅9kg、拥有可调自走接驳速度和温控,操作简单,无需技术指导和任何粘合剂,仅取决于个人操作熟练和灵活程度。 使用时只要将拼接画面两端压缝层叠临时固定,开机预热2分钟后,滚轮对准压缝边缘,根据布质厚度和材料、及地面情况调好温度和速度,放 下手柄,插入热风头到接缝处上下层间,自走压合完毕后,便大功告成。
  该机适用范围:喷绘布、灯箱布、枷网帆布、遮阳棚等涂层膜结构(聚乙烯、聚丙烯、聚氯乙烯等可热熔材质)平面的拼接。
  使用方法:
  1) 将拼接画面两端距压缝40mm处用胶带或夹子等固定牢固;
  2) 开机预热2分钟左右;
  3) 将机器放在拼接画面端头压缝处,滚轮对准压缝边缘;
  4) 根据布质厚度和材料、及地面情况调好温度和速度,放下手柄,插入热风头到接缝处上下层间,自走压合完毕后,便大功功告成。
  5) 注意事项:完成工作后,为保护电热芯不易过早老化,一定要做降温处理:扳起热风头、调低温度(到温度调节旋钮数字1-2处)、3-5分钟后再关闭温度为零。特别地,遇到正工作中突然断电时,也一定要也要先扳起热风头,再把温控刻度调低,再去考虑电源接通的问题。特别注意,要保持接缝处地面的平坦(水泥或瓷地砖等坚硬耐热质地为最佳),以利于热拼压合。
  
  无胶广告喷绘布拼接机操作就这么简单,无需技术指导和任何粘合剂,仅个人操作,该机以它独有的优势终将会在喷绘行业火爆。

        Brief introduction of Poster Heat Jointer
Good companion for painting machine ----Poster Heat Jointer Machine may join disjunct advertising poster surface without mucilage.
Know to all, the way to bond disjunct advertising poster surfaces, we usually use mucilage, such as the 502 glue to join them together in one, but the means have a lot of disadvantages, such as:
(1)Almost all of these kinds of bond are harmful on human health; (2)When work, the operation is slow and is not too satisfied in strength with the glue, to get a good strength, usually we must proceed a special handling, such as whet the surface to make the surface not smoothed, so it may cost more workers; (3)The air temperature may influence the stick strength, in low temperature environment, the bond effect maybe bad.The Heat-Jointer Machine Without Mucilage, will be a more efficient companion for advertising material instead of the 502 glue.
It can nicely solve the above existent problems, and may save more manpower and work field, for example, a PVC jointed painting with 200 meters long surface can be easily coalesced together and well matched, all the works can be well finished by a single person on only a heat-resistant and smooth base ground about 30 square meters.
The machine is designed self-moveable, the volume is small, the whole weight only 9 kilogram, the work temperature and self-move speed is adjustable;
The HEAT JOINTER Machine, to join disjunct poster banner without mucilage, is constructed simple, easy to maintain, The volume is small, the whole weight only 9 kilogram, the work temperature and self-move speed is adjustable; the operation is also simple,and needs not much guide to operate.
When use: 1) Immobilise both ends of each disjunct poster surface with something such as stick belt or clamp, and leave about 30-40mm wide overlap edge on each disjunct poster surface edge; 2) Turn on the machine, prepare warm up about 2 minutes; 3) Bring up the machine, and place the roll at the end of the overlap edge; 4) According to quality and thickness of the poster surface material, consider the ground circumstance, adjust the proper temperature and speed, handle the Fuse machine Gun down and insert it between the two poster banner edges, then the machine start running, after go pass the overlap edge, the two disjunct banners will be well joined in one.
Application:laminate and bond up disjunct flat painting surface made of heat-melted material, such as outdoor advertising poster,PVC cloth & PE fabric Canvas, outdoor poster banner,plastic surface, Sailcloth...etc.


.